3 D Vacumepress

3D vacume press

With this press you can do 3D for tiles with round corner, phone covers, plates, shot glasses and more.

You can also make 8 mugs oe 6 tiles, 6 phone covers in one time.

See for details of printing below.or video at Dutch description

Size 63 wide 47 deep and 28 high, weight 25 kilo

More details

Printing  time and temperature:

1 will be one push for heating, 2 will be for heating from upside and downside.

Mugs the paper from ear to ear so also paper where will come no inmage. 

Item                                    Heating                  Time            Temperature C                    Extra information             Vacume

Phone cover                      1 / 2                        7    min        185                                      Possible 6 at a time               Y

Rock stone                        1 / 2                        7,5 min        200                                          ,,         2 at a time              Y

Mugs                                  1 / 2                        10 / 11         200       11 min with more        ,,         8 at a time            N open side to bottom

Mug Senseo                      1 / 2                         8   mim       200                                                                                  Y open side to bottom

Mug color change              1 / 2                        9   min         185                                                     8 at a time            N open side to bottom

Tiles                                   1 / 2                        7   min         200         9 min with more                   4 or 6 at a time      Y

Tiles 14,5 x 14,5 and 14,7 x 19,7                     5   min         200         7 min with more                                                 Y

Glass, cut. b. clock small   1 / 2                       6   min         200         8 min with more                   2 at a time             Y  

Glass, cut. b. clock big       1 / 2                       8   min         200                                                                                   Y

Glass mug                          1 / 2                       8   min         200         10 min with more                 8 at a time             N    Open side to bottom

Glass Shotglass                 1 / 2                       7   min         200                                                     7 at a time             Y    With special holder

Astray                                 1 / 2                      10  min         200         10 min with more                10 at a time            Y

Bidon                                   1 / 2                       5   min         200                                                      3 at a time           N

Textile                                  1                            3   min         200     Use cutting board, see video                              Y

Plates                                  1 / 2                       8   min         200      Small plate, big plate 10                                         Y

Print on folie Pap.1425 en let it dry after printing. Put it in the pres and than put a little paper between the image and the plate. Start vacume and when it will be vacume put the vacume off, take out the piece of paper and get vacume on again.

 

Polymer (Plastic) Plate printing by  vacumepress

 

Print on the folie, Image 1 cm bigger than the plate.

Put the press to 160 degrees Celsius

You already may put the plate into the press without the image

When the press reach the temperature put vacume on without the image for 2 minutes.

Open now the press, plate will be total flat, put off vacume and lay your print on the plate.

Wait 10 seconds and the folie will become softer.

Now push on vacume again for 5 minutes, look before you close the press that the folie will go well as you can easy strike the folie with your fingers.

Plate will come back in his shape when you will take him out of the press

Cart

No products

€ 0,00 Shipping
€ 0,00 Total

Prices are tax excluded

Check out

Contact us

Our support hotline is available 24/7.

News/Nieuws & Updates



Forever Flex soft no cut foils.


klik hier voor Forever